Kategoria BISAC: Transportation >> Public Transportation

The activities of the semiconductor industry to introduce a new, large wafer diameter were triggered by expected potential overall savings - cost and resource - and an anticipated increasing demand for Silicon wafers. In the beginning, around 1994, agreement on the diameter of the next wafer generation had to be achieved and finally 300 mm was globally accepted to be the next wafer diameter, a decision obtained at international summits in 1994/1995, based on the work of a SEMI task force.

Several workshops on 300 mm wafers have been held by SEMI, JSNM and other organizations during...

Held from 3-5 September 1997 in Nantes, France, this was the fifth of the IFAC series of triennial Symposia on Robot Control. The final selection lead to 126 papers (from 200 submissions) in the Technical Program. This consisted of 33 sessions disposed in 3 parallel tracks and brought together contributions from 298 leading researchers.

The papers covered a range of topics relevant to the field of robot control, including modelling and identification, force and compliance control, robot control techniques, vision control, grasp control, flexible robots, non holonomic robotic...

Each chapter represents a separate unit which taken together create a better understanding of the whole subject. Topics include the causal agents of postharvest diseases of fruits and vegetables, their sources and their ways of penetration into the host; factors that may accelerate the development of the pathogen in the host - and those that suppress them; a list of the main pathogens of fruits...

The central topic discussed by the committee was that of the minimum reinforcement in concrete members. The minimum amount of reinforcement is defined as that for which "peak load at first concrete cracking" and "ultimate load after steel yielding" are equal. In this way, any brittle behaviour...

The conference aimed to juxtapose two great ergonomic themes - the under-developed ethos of the affluent societies and the technologically advanced ethos of the most affluent...

These proceedings contain the reviewed papers presented at the Symposium J on "Ion Implantation into Semiconductors, Oxides and Ceramics," which was held at the Spring Meeting of the European Materials Research Society in Strasbourg, France, 16-19, June 1998. The symposium attracted 110 contributions, with authors from 31 nations in 5 continents. It was thereby the largest in a series of E-MRS ion beam symposia, documenting the importance of ion beam techniques and research in this area.

The aim of this symposium was to provide a forum for the discussion of new results in the...

The rapid technological developments during the later half of the 20th century have demanded materials that are stronger, capable of use at much higher temperatures, more corrosion-resistant, and much less expensive than those currently used. These demands become even more significant on the threshold of the new century and the millennium. Significant improvements in properties can only be achieved by processing the materials under far-from-equilibrium (or non-equilibrium) conditions. Several new processing technologies have been developed during the past few decades including, rapid...

Without the effective participation of developing Asia, a climate crisis is certain. Within developing Asia, the key to averting such a crisis lies in low carbon transport. China, India and Asia's other emerging economies could promote fuel efficient vehicles, public transport, and sustainable urban planning. Or they could become locked into inefficient vehicles, energy intensive infrastructure, and suburban sprawl. The path they choose will have long-term implications for the entire world. And it will depend upon the extent to which they adopt a co-benefit approach.

A co-benefit...

These two volumes contain the Proceedings of the 9th IFAC symposium on Information Control in Manufacturing which took place in Nancy and Metz, France, between 24-26 June, 1998.

This INCOM'98 program had six main themes which focused on the role of information for automating manufacturing operations; the role of information for integrating and distributing automated manufacturing activities in the whole Enterprise and; the role of information for enhancing synergies between humans and machines.

This year's symposium drew attention from more than 35 countries, and the number...

The aim of the Conference is to bring together researchers from universities and...

Rapid Thermal Processing (RTP) is a well established single-wafer technology in USLI semiconductor manufacturing and electrical engineering, as well as in materials science. The biggest advantage of RTP is that it eliminates the long-ramp-up and ramp-down times associated with furnaces, enabling a significant reduction in the thermal budget. Today, RTP is in production use for source/drain implant annealing, contact alloying, formation of refractory nitrides and silicides and thin gate dielectric (oxide) formation. The aim of Symposium I was to provide an overview of the latest...